日韩色图在线_奇米在线视频_最近免费中文字幕mv视频_2019中文字幕 - 自拍偷拍网站

故障代碼

錯誤含義

具體描述

FIP/Corrective Action

-

Y Toner Life Warning

黃色碳粉壽命警告

The yellow toner cartridge has reached the set toner supply time limit but it can still work.

黃色碳粉盒已達到規定時限碳粉供應，但它仍然可以工作。

FIP-1 75

-

M Toner Life Warning

紅色碳粉壽命警告

The magenta toner cartridge has reached the set toner supply time limit but it can still work.

紅色碳粉盒已達到規定時限碳粉供應，但它仍然可以工作。

FIP-1 76

-

C Toner Life Warning

青色碳粉壽命警告

The cyan toner cartridge has reached the set toner supply time limit but it can still work.

青色碳粉盒的已達到規定時限碳粉供應，但它仍然可以工作

FIP-1 77

-

K Toner Life Warning

黑色碳粉壽命警告

The black toner cartridge has reached the set toner supply time limit but it can still work.

黑色碳粉盒的已達到規定時限碳粉供應，但它仍然可以工作

FIP-1 78

-

Toner Bottle Life Warning

碳粉滿警告

The waste toner bottle is detected FULL by the SENSOR TNER FULL but can still work

廢碳粉檢測傳感器到檢測廢碳粉瓶滿，但仍然可以工作。

FIP-1 79

-

Xero CRU Life Warning

感光鼓(CRU)壽命警告

The drum has exceeded its specified rotation count but it can still work.

鼓已超過其指定的旋轉數，但它仍然可以工作。

FIP-1 80

%s Check paper

％本票紙

IOT Paper Size Mismatch

互操作性測試紙張尺寸不匹配

Paper Size Mismatch detected.

紙張尺寸不匹配檢測。    (打開/關閉托盤或刪除旁路紙盤并重新加載文件)

Open/close the tray or remove and reload paper in Bypass Tray.

(No LCD Display)

無液晶顯示器

Static Jam (Remain at OHP)

靜態果醬（留在鉑）

The SENSOR OHP was turned ON at Power ON or when the I/L was closed. (Static Jam)

該傳感器鉑被打開或上電時的I / L的關閉。（靜態果醬）

FIP-1 39

001-358

IOT Fan Error Fuser

互操作性測試范錯誤定影

Fan Error Fuser detected.范錯誤定影檢測。

Power OFF/ON

001-360

IOT Fan Error Rear

范錯誤后互聯互通

Fan Error Rear detected.范后發現錯誤。

Power OFF/ON

003-356

NVRAM ErrorNVRAM中錯誤

An error occurred in the NVRAM on the PWBA MCU.

錯誤發生在微控制器上的PWBA NVRAM中。

FIP-1 43

004-310

Communication Error Feeder

直屬通信錯誤

A communication error occurred between the PWBA MCU and the feeder.

阿之間發生的通訊錯誤的PWBA MCU和接駁。

FIP-1 40

004-311

Communication Error Duplex

通訊錯誤雙工

A communication error occurred between the PWBA MCU and the Duplex.

阿之間發生的通訊錯誤的PWBA MCU和雙工。

FIP-1 41

004-321

TR0 Failure

TR0傳感器故障

The PWBA MCU did not receive the output signals from the SENSOR TR-0 (TR0 Sensor) at the specified timing.

PWBA MCU沒有在指定定時方面收到從傳感器TR-0((TR0傳感器)輸出信號.。

FIP-1 44

004-324

Humidity Sensor Error

濕度傳感器錯誤

The inputs from the SENSOR HUM & TEMP are out of the specifications.

從本田和溫度傳感器的輸入，是從規格

FIP-1 58

004-332

Deve Home Position Sensor Error

德韋首頁位置傳感器錯誤

The PWBA MCU did not receive the output signals from the Rotary Home Position Sensor within the specified time after the Rotary Developer had started rotation.

在指定作為時間以內PWBA MCU 不確實收到從旋轉的國內位置傳感器從輸出到信號，在旋轉的開發者已經以開始轉動之后。

FIP-1 46